when camera is washed out(too bright) at CVBS mode, set lens as manual .
Hit OK button on UTC controller to bring up Camera OSD menu as below.
And,Change Lens from 'Auto' to 'Manual' and 'Save &Exit'
Statistics: Posted by Wade — September 4th, 2019, 2:02 pm
]]>
this camera has 6~22mm manual adjust lens.
To identity the letter on the tag, it need to be zoomed in narrower than 15 ft wide in target area.
And, distance from camera to target area need to be closer than 80ft.
2. setting brightness of license plate at night
There is on screen menu setting in the camera as above picture.
-Up/Down : move cursor
-Left/Right : change setting
Mode: select Road
Speed: select between 120, 150 and 180km depends on the brightness of license plate at night.
this speed affect the brightness of picture for both day and night time.
(when it is slower than 120km/h, tag at day time could be too bright.)
<Scene Bri, LED light>
this two setting affect the night picture brightness. the larger, the brighter.
<CDS Start>
To switch night mode earlier , changes it to 2
(the smaller it is, it switches to B/W at brighter condition)
1: Day mode all the time, 5:default
Because the brightness changes depends on the distance from LED of camera to vehicle,
installer need to check the brightness at night and select appropriate speed.
the faster it is , it becomes darker.
the slower it is, it becomes brighter.
<Tip1>
Each speed setting is preset with specified shutter speed as below.
30km/h-Flickerless, 60km-1/240s, 90km-1/480s, 120km-1/1000s,150km- 1/2000s, 180km-1/5000s
<Tip2>
do not adjust shutter speed/AGC/Brightness via UTC because it goes back preset setting by LCD controller when it power reboot.
<Tip3>
On screen setting as LED Light and CDS sensor setting.
<How to switch video TVI/CVBS>
Statistics: Posted by Wade — April 17th, 2019, 5:53 pm
]]>
Go to ‘DOME’ using up/down arrows and Hit ‘Right Arrow ‘ to go into ‘DOME’
Go to ‘COMM’ using up/down arrows and Hit ‘Right Arrow ‘ to go into ‘COMM’
Hit Right Arrow to log in ‘CHECK ID’
Use Up/Down arrows to change ‘CHECK ID’ same as ‘DEVICE ID’
Move to TARGET ID and hit 'Right Arrow' to log in.
Change ID by up/down as you need.
Hit Left Arrow to log out from ‘Check ID’
SAVE and Exit
Statistics: Posted by Wade — December 4th, 2018, 2:40 pm
]]>
Statistics: Posted by Wade — March 13th, 2018, 2:55 pm
]]>
-TV2BD : Left:CVBS, Down:TVI, Right:AHD,Up:CVI
-TV3M : Left: CVBS, Right: TVI, Up: AHD, Down: CVI
-Pano-2180W: Left:TVI, Right:CVBS, Up:AHD, Down:CVI
-SENS HDB : hold joystick to left for 10 seconds to switch between CVBS and TVI
Statistics: Posted by Wade — October 30th, 2017, 7:22 pm
]]>
1. First way(Short cut)
*Nuvis DVR : coaxtron and PELCO D in Nuvis DVR does not support preset over 100.
but TCL-PELCO D supports this shortcut. use TCL-PELCO D.
*Atlas DVR : Pelco D and Coaxtron protocol support all these 3 digit preset.
(Coaxtron does not work at CVBS)
Call Preset 137 twice : Switch to AHD
Call Preset 138 twice : Switch to TVI
Call Preset 139 twice : Switch to CVI
Call Preset 140 twice : Switch to CVBS
Call Preset 115 twice : Switch to 30fps
Call Preset 116 twice : Switch to 25fps
swtiching NTSC/PAL at CVBS is only available below second way(OSD menu)
2. Second way(OSD menu)
call preset 102 twice : to open OSD menu
Zoom + : Up
Zoom - : down
Focus + : right
Focus - : Left
call preset 102 twice : Enter
select TVI(THD)/CVI(CHD)/AHD/CVBS at camera menu below.
select NTSC/PAL in main menu below.
Statistics: Posted by Wade — September 15th, 2017, 2:35 pm
]]>
Normally when you want to have PTZ joystick controller for TVI PTZ camera, you need to use UTC from DVR to TVI PTZ . And, use RS485 from controller to TVI PTZ camera. All pan/tilt/zoom work by both UTC and controller.
In the DVR you need to pick one protocol for one camera.
When you use RS485, pick pelco D and when you use UTC, pick coaxtron protocol.
From one DVR you cannot use both pelco D and coaxtron for one camera.
Statistics: Posted by Cdin — January 28th, 2016, 11:58 am
]]>
Statistics: Posted by Guest — January 14th, 2016, 3:52 pm
]]>
Statistics: Posted by Guest — January 7th, 2016, 10:34 am
]]>
1.DVR PTZ protocol :
-Nuvis TVID DVR: Hikvision C(coaxtron) - this is default.
-Atlas TVI DVR: coaxtron- Pelco D is default
2.Wire configure
-Don’t need extra wire. It control over video wire.
3.Camera setup
- do not need extra setup. auto focus is default
-“Iris open” or ”preset 95” for camera OSD menu in case you want to adjust camera
4.How to zoom in/out
-From DVR : use zoom in/out of PTZ control buttons
-From Camera : “up’ is zoom in and “down” is zoom out
Statistics: Posted by Guest — January 6th, 2016, 2:49 pm
]]>